WN

WN (https://www.wn.se/forum/index.php)
-   Off Topic (https://www.wn.se/forum/forumdisplay.php?f=7)
-   -   Min nya hobby... (https://www.wn.se/forum/showthread.php?t=17701)

Alpha 2006-11-24 09:01

http://members.cox.net/crandall11/money/
Text/Bild Källa: http://members.cox.net/crandall11/money/shirt/

The Shirt
As with all these designs, try to start with a relatively clean, crisp bill. It will make it much easier. All folds should be sharply creased. It helps to go over the fold with a fingernail on a flat, hard surface.


1.
http://members.cox.net/crandall11/mo...irt/shirt1.jpg
Start by folding the bill precisely in half lengthwise. (I prefer to fold in toward the front of the bill. I think it produces a nicer design on the end product. For your first attempt, it will be easier to follow exactly the same orientation on the bill as shown in the photos.) Unfold the bill, leaving the crease produced by the fold for the next step.


2.
http://members.cox.net/crandall11/mo...irt/shirt2.jpg
Fold the bill one quarter of the way in from each side lengthwise. The edge of the bill should just meet the crease made by the fold in the previous step. Do this for both sides as shown.


3.
http://members.cox.net/crandall11/mo...irt/shirt3.jpg
Turn the bill over. Fold the white of one end over as shown. This will become the collar in the next step. (If the bill is printed unevenly, use the wider edge.)


4.
http://members.cox.net/crandall11/mo...irt/shirt4.jpg
Turn the bill over again. From this side, angle-in the two corners from the end you folded in the last step. The two points should meet precisely at the centerline. The angle is not terribly important, but should be about the same as shown in the photo.


5.
http://members.cox.net/crandall11/mo...irt/shirt5.jpg
Fold a little less than one third of the bill lengthwise from the opposite end as shown. If you're following in the same orientation as the photos, use the markings on the bill for a fold point. (Notice that the edge of the bill just meets the word "OF" on the reverse printing.) If you fold too little, the shirt will appear too long in the end. If you fold too much, the next step will not work. See below.


6.
http://members.cox.net/crandall11/mo...irt/shirt6.jpg
Now you will fold inward in the same direction, tucking the previous fold under the "collar" created in step 4. So far it looks kinda 'nifty, and if you know it is supposed to look like a shirt, you get the collar concept. But wait, there's more...


7.
http://members.cox.net/crandall11/mo...irt/shirt7.jpg
Gently unfold the previous two folds, keeping the creases. On the lateral fold furthest from the collar, refold it strait across as shown. (On the flatbed scanner, this made a bit of a mess of it, but it is fairly easy in 3D.)


8.
http://members.cox.net/crandall11/mo...irt/shirt8.jpg
(This step is hard to describe, but it is actually fairly easy.) You are going to introduce two new folds on each "sleeve". I do this by holding each side of the previous fold between thumb and forefinger in the orientation shown, just on either side of the vertical fold as shown. Just force the angle to close slightly, and force the extra paper inside the vertical folds. Once you've got it looking right, force the insides to crease by pressing on a hard surface. (Try looking at the next photo - like I said, it is hard to describe!)


9.
http://members.cox.net/crandall11/mo...irt/shirt9.jpg
(This is a close-up of what the fold should look like when complete.) Do this for both sides.


10.
http://members.cox.net/crandall11/money/sh...irt/shirt10.jpg
(This is what it should look like after both sides are complete.)


11.
http://members.cox.net/crandall11/mo...rt/shirt11.jpg
When you re-tuck the fold you've been working on back under the collar, you're done! It should look about like this. With the basic shape, the collar and the sleeves, it should be recognizable. Once you've done a few, you can try folding the whole thing into the reverse side, leaving the obverse side out. (Like I said, I think this looks better. This is especially true with 1 dollar bills where the edge seal on the reverse under the collar looks a little bit like a necklace.)

YOU LIKE IT HUHUHH?? ;)

(admin, jag råkade posta i fel kategori.. flytta tråden till offtopic tack :unsure: )

Hofvet 2006-11-24 17:02

Haha :D gick fint med en svensk 20-lapp med.

Tynnhammar 2006-11-24 17:12

Citat:

Originally posted by Hofvet@Nov 24 2006, 18:02
Haha :D gick fint med en svensk 20-lapp med.

Bildbevis tack! :D

Eddie 2006-11-24 17:35

Hehe det där var länge sedan man gjorde. 20 lappar funkar skitbra, då får man även en slips av gåsen eller vad det är på lappen.

Jonas 2006-11-24 18:16

Citat:

Originally posted by Eddie@Nov 24 2006, 18:35
Hehe det där var länge sedan man gjorde. 20 lappar funkar skitbra, då får man även en slips av gåsen eller vad det är på lappen.
Har för mig att bankerna delade ut beskrivning om hur man kunde göra en kostym utav en 20-lapp.

(Skjorta + Byxor)

Björn 2006-11-24 19:11

en klassiker

ToBad 2006-11-24 19:48

Vem var det sa sa att vi datanördar inte kan roa oss en fredagkväll?

LRantalainen 2006-11-24 19:52

Citat:

Originally posted by ToBad@Nov 24 2006, 20:48
Vem var det sa sa att vi datanördar inte kan roa oss en fredagkväll?

haha :D

Hofvet 2006-11-25 02:18

2 bifogad(e) fil(er)
Citat:

Ursprungligen postat av Tynnhammar
Citat:

Ursprungligen postat av Hofvet
Haha :D gick fint med en svensk 20-lapp med.

Bildbevis tack! :D

Jag hann vika upp den, men det funkade med en hundralapp med!

Tynnhammar 2006-11-25 16:29

Hehe! Fin krage också :).


Alla tider är GMT +2. Klockan är nu 07:34.

Programvara från: vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Svensk översättning av: Anders Pettersson